Devices You Need to Install a New Bath Tub
Devices You Need to Install a New Bath Tub
Blog Article
Just how do you really feel with regards to A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't exactly rocket science, however it does require solid plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough task. If the old tub is easily accessible, the job can relocate speedily; if you have to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will need an assistant to vacate the old bathtub and set in the brand-new one. See to it you have qualified yourself for the task and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one prior to you begin. Chances are you may need a specialist plumber to make tube connections.
This short article will assist you mount a brand-new bath tub in your bathroom if you have already purchased a brand-new bathtub as well as do not require to transform the setup of your previous water supply pipes.
Your tools and material checklist ought to make up the following:
Planning for the Setup
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome because of the restricted gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the staying water that will certainly come from the pipes. When the supply pipes have actually been removed, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost adaptable tap port to the appropriate supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the water system and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub must wait till the bath tub has been utilized at the very least when as this will settle it into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in location between the faucet as well as the sink. Protect the faucet in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former type should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to fracture a stiff seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing problems with wetness and also feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes and cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that page on A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. Sharing is caring. Who knows, you may just be helping someone out. We take joy in reading our article about Installing A Bathtub.
Click
Report this page